65106 Fan Vent Motor for Nutone C68627 NEW

CRC6,180.71
SKU:
65106
UPC:
840899126128
Condition:
New

Product Description

Packard Vent Fan Motor 65106 for Nutone C68627

This is a Direct Replacement for Nutone number C68627 and will also replace the 53709000 (you may have to turn the bolts around)

Motor Specifications:

  • .90 Amps
  • CCW Rotation as Viewing Shaft End
  • 7/32" X 2-3/8" Long Shaft, w/ Flat
  • 5/8" Stack
  • 2 Stud Mount on Shaft End, Studs Measure 1-7/8" Apart, Center to Center
  • Standard Plug Cord Attached

Product Reviews

Write a Review
  • 5
    Perfect fit and function

    Posted by Don on 29th Apr 2020

    Ordered this to replace a fan motor that had burned out in our bathroom vent. The product was a perfect fit. It is quieter than the original!

  • 5
    Direct repalcement works great

    Posted by Unknown on 12th Aug 2019

    The old motor was getting noisy and needed replacing. Fast shipping.

  • 5
    Replacement fan for Broan 665N bath exhaust fan

    Posted by Unknown on 24th Aug 2018

    I can verify the other reviews stating this works to replace the exhaust fan motor in a Broan 665N bathroom exhaust fan. Had to reverse the mounting screws; to do this first remove the 2 long screws. You then have to remove the round metal castings on the front and back of the motor and reinstall them on the opposite side. Then install the screws. I re-used the original plastic squirrel cage fan after washing out the accumulated dust. I also treated the rusting housing where the fan goes with Rust Reformer.

  • 5
    Saved me a bunch of money

    Posted by tom on 12th May 2018

    Great fan motor-its quiet- it was easily modified to replace a bad motor in a 665N bathroom light/fan/heater. It saved me having to retrofit a new unit in the existing opening. The price was great and shipping was prompt. I am so happy to have found McCombs Supply. I was up and running 20 minutes after opening the package

  • 4
    Got my vent working again

    Posted by lmeile on 8th May 2018

    The replacement fan motor was suggested for my vent. As others have mentioned, the mounting bolts had to be reversed -- a very simple task. In my case, the new motor shaft was larger in diameter than the old one so I had to drill out the impeller hub to be able to press it onto the new shaft. Having a drill press helped assure that the drilled hole was straight so the impeller did not wobble. Still no big deal. The fan now works again and at a very reasonable price with prompt shipping.

  • 5
    Great buy

    Posted by Unknown on 10th Apr 2018

    Exactly the fan needed after a very long search. Great buy and superior service.

  • 5
    Replacement motor

    Posted by Unknown on 23rd Feb 2018

    Not knowing the old motor specifications, serial number, I was able to match the replacement motor by the web site specifications, measurement, and picture. Perfect replacement motor, just fit right. Excellent service, shipped fast, got it in 3 days.

  • 5
    Nutone replacement motor

    Posted by Unknown on 18th Oct 2016

    Very easy, flipped the bearing, tested ok.Installation took 5 min. Hope to get another 20 years out of this motor.

  • 4
    Nutone replacement motot

    Posted by Denny on 1st Sep 2016

    Received this item in only a few days after ordering, fit my fan house with only having to change the side the long bolts come out of it as other have mentioned.

  • 4
    Easy swap for a motor deemed "obsolete" by NuTone

    Posted by Brad on 20th Jul 2016

    Have a NuTone / Broan 668N with worn out motor bushings. To get this one to work, all that needed to be done was swap the bearing mounts and bolts with each other on the new motor. Took under 5 minutes. Make sure you tighten the bolts incrementally and evenly, as not doing so can bind the rotor shaft or make it noisy. I found it easiest to plug it in and run the motor without the impeller from the old assembly AS I tightened the bolts, so I could observe any binding or noise. YMMV

  • 5
    Simple to repair older heater/fan...

    Posted by Unknown on 2nd Jul 2016

    We have two Nutone 9425F Bulb Heater fans and the vent motor went out on both after 30+ years. These replacements are the perfect match and we received them in days. Could have replaced the fans for many $$$ and hours of work, but for less than $20 they a humming like new!

  • 5
    Cost effective repair

    Posted by Joe Fucito on 22nd Jun 2016

    Finally after 30 years, bathroom exhaust fan motor failed. Couldn't go without exhaust fan but replacing complete unit would have led to extensive work and cost in a space that will undergo a complete remodel in about 2 years. Stumbled across this motor at McCombs and it was the perfect solution. Web order process easy, communication re processing and shipping of my order was great, and product was the exact one I needed.

  • 5
    Arrived fast and just as described

    Posted by Julia on 10th May 2016

    McCombs had just the part I needed to replace an exhaust fan in my older home. The web site made it easy to find the part and it arrived earlier than expected.

  • 5
    Prompt and efficient service

    Posted by Clovis Joseph on 17th Feb 2016

    The person on the phone was courteous and helpful I received fast service.
    Thank you,

    Clovis Joseph

  • 5
    Nice replacement for Nutone 665N vent fan

    Posted by Donald Fowler on 7th Dec 2015

    I used this motor to replace the vent fan in a Nutone 665N heat/vent/light unit. Original motor was from Jakel. The Packard 65106 worked fine - I just had to turn the bolts around as advertised. Price was great - much cheaper than the CTS C53709 53709-000 J238-062-6146 motor advertised on Amazon.

  • 5
    Excellent Service

    Posted by Ed Ribback on 14th Aug 2015

    The motor was exactly what I needed. The shipment arrived much faster than expected.